Home » Guides » How to Reset Dodge Charger Computer

How to Reset Dodge Charger Computer

The first step is to disconnect the battery. Once the battery is disconnected, press and hold the power button for 15 seconds. This will discharged any residual power in the system.

Next, reconnect the negative cable to the battery terminal followed by the positive cable. Finally, start the engine and let it idle for about 10 minutes to allow the computer to reset itself.

  • Locate the fuse box in your Dodge Charger
  • This is usually located under the hood, near the battery
  • Find the fuse for the computer system
  • It should be labeled “PCM” or “ECM
  • Use a fuse puller or pliers to remove the fuse from the box
  • Wait 30 seconds before replacing the fuse
  • This will reset the computer system and clear any stored codes
How to Reset Dodge Charger Computer

Credit: www.hendrickdodge.com

How Do I Reset My Dodge Computer?

Dodge vehicles are equipped with computers that control all of the vehicle’s systems. When something goes wrong with the computer, it needs to be reset in order to start working again. There are a few different ways to reset a Dodge computer, depending on what type of problem you’re having.

If your Dodge is having trouble starting up, or if the engine is stalling, you may need to reset the computer. To do this, disconnect the negative battery cable for about 30 seconds and then reconnect it. This will erase any stored codes in the computer and allow it to start fresh.

If your Dodge is experiencing problems with its electrical system, such as power windows or door locks not working properly, you can try resetting the Body Control Module (BCM). To do this, disconnect the negative battery cable and then press and hold the BCM programming button for about 15 seconds. Reconnect the negative battery cable and see if that solves the problem.

If your vehicle has an On-Board Diagnostics (OBD) port, you can use it to reset the Dodge computer. First, locate the OBD port under the dash near the steering column. Then hook up an OBD scanner tool and follow its instructions to clear any codes stored in the computer memory.

How Do You Reset the Pcm on a 2014 Dodge Charger?

If you own a 2014 Dodge Charger, you may need to reset the PCM from time to time. This can be done easily by following these steps: 1. Locate the fuse box under the hood of your car.

2. Find the fuse labeled “PCM” and remove it. 3. Wait for 30 seconds before replacing the fuse. 4. Start your car and let it idle for a few minutes.

How Do You Reset a Charger?

How to Reset a Charger If your charger isn’t working properly, resetting it may fix the problem. Here’s how to do it:

Unplug the charger from the power outlet and remove any batteries. Press and hold the power button for 30 seconds. This will discharge any residual energy in the capacitor.

Plug the charger back into the power outlet and insert the batteries. Press and hold the power button again for 30 seconds. This will reset the charging circuitry.

Try using the charger now to see if it works properly. If your charger still isn’t working after following these steps, it may be time to replace it.

Fuse 31 PCM Reset

How to Reset Computer on 2008 Dodge Charger

If your 2008 Dodge Charger needs a reset, there are a few steps you’ll need to follow. First, disconnect the battery and then reconnect it after about 30 seconds. Next, locate the fuse box under the hood and remove the “PCM/ASD” fuse.

Once that’s been removed, turn on the ignition and let the car run for about 10 minutes. Finally, turn off the ignition and reinsert the fuse. That’s it!

Your 2008 Dodge Charger should now be reset.

Conclusion

If your Dodge Charger is acting up, it may be time to reset the computer. This can be done by disconnecting the battery for 30 minutes or so. You may also need to remove the positive and negative terminals from the battery.

Once you’ve done that, reconnect everything and start your car. The computer should now be reset and hopefully, your car will be running better!