If your car needs a new tail light assembly, you know just how frustrating it can be to try and find the right part and get it installed. There are so many different types and models of cars, and not all tail light assemblies are created equal. In this article, we’re going to walk you through the process of replacing a tail light assembly; from finding the right part to installing it. We’ll also provide some tips on how to make the installation process as smooth as possible. So don’t wait – get started on replacing your tail light assembly today!
What is a Tail Light Assembly?
A tail light assembly is a component on a car that helps visibility while driving. It’s made up of the light bulb, the housing, and the wiring. The housing fits over the light bulb and holds it in place. The wiring connects the housing to the light switch or module. When it comes time to replace your tail light assembly, you’ll need to do a few things: remove the old one, install the new one, wire it up, and reinstall the cover. Here’s a guide on how to do each step:
1) Remove the old tail light assembly by taking off the screws that hold it in place. Be sure to note where they went so you can put them back when you install the new one.
2) Install the new tail light assembly by reattaching the screws that were removed in step 1. Make sure that everything fit properly before tightening down the screws.
3) Wire up your new tail light assembly by connecting it to your vehicle’s existing electrical system. This can be done through either an inline connector or a harness. Follow your car’s specific instructions for this step.
4) Reinstall the cover onto your tail light assembly by attaching it with screws that were previously removed in step 1. Be sure to torque these screws down properly so that they don’t come loose again later on.
The Different Types of Tail Lights
When your car’s tail light assembly needs to be replaced, there are three types you need to be aware of: the round type, the square type, and the rectangle type. Round tail lights are usually the cheapest and simplest to replace, while the more complex square and rectangle tail lights tend to cost a bit more but offer better quality.
If your car has a round tail light assembly, you will need to remove the cover on the back of your car. Inside you will see two small screws that hold the cover in place. Once those screws have been removed, simply pull out the cover and replace it with a new one.
If your car has a square or rectangle tail light assembly, you will need to remove both covers from the back of your car. Inside you will see four screws that hold each cover in place. Once those screws have been removed, carefully pry off each cover and replace it with a new one. Make sure to match up the holes in each cover so they line up correctly when they’re re-installed.
Finally, if your car has round turn signals but rectangular taillights, you will need to replace both assemblies at once. The process is similar to replacing either type of taillight separately, except that you will also need to remove two Torx screws from around the perimeter of each turn signal lens housing.
How to Replace a Tail Light Assembly
Replacing a tail light assembly on a car can be relatively easy, depending on the make and model of the car. In most cases, all you will need is a Phillips head screwdriver and a wrench. To begin, locate the tail light socket on the car and remove the four screws that hold it in place. Once those are out, pull out the light assembly and replace it with a new one. Make sure to torque the screws back to their original specs and re-install the light socket.
Pros and Cons of Replacing a Tail Light Assembly
Replacing a tail light assembly is an easy and affordable fix that can improve the safety of your car. However, there are a few pros and cons to consider before making the repair. Here are the benefits of replacing a tail light assembly:
-Easier To Repair: A broken or damaged tail light assembly makes it difficult to see in traffic, which can lead to accidents. Replacing the entire assembly instead of just the lightbulb ensures that the issue is fixed and you’re back in business.
-More Visibility: A good replacement tail light assembly will give you improved visibility while driving, which is especially important during night time driving. Without proper illumination, you could end up getting into an accident.
-Cheaper Than Repairs: Replacing a tail light assembly is much cheaper than dealing with repairs or replacements later on down the road. This is especially true if you use your car regularly and keep it maintained.
There are also some cons to consider when deciding whether or not to replace a tail light assembly. Some of these include:
-Downtime: Replacing a tail light assembly can be a pricey fix, so be prepared for some downtime if you make the repair. Depending on the severity of the damage, you may need to wait for parts or take your car in for repairs. This can add up over time if you depend on your car for transportation regularly.
Conclusion
If your tail light is not working, it’s time to replace the assembly. This guide will show you how to do it without any trouble. Follow the instructions carefully and you should be good to go in no time at all. Good luck!